Filter price review or Delta Xero at your site?Book a meeting

Delta Xero cartridges in stock
Economics

What does dirty oil cost?

Dirty oil rarely appears as a line in the budget. It hides in oil purchases, spare parts, overtime and production that stands still. Here are the three ways it costs you, counted with figures from the case studies. Below the article you can calculate your own oil changes.

Where does the cost come from?

Item What it consists of
Oil changes New oil, disposal of used oil, labour hours
Failures Pumps, valves and cylinders to be replaced, plus fitter hours
Downtime Production or operation that stands still during changes and repairs
Knock-on costs Filters that block, and wear that shortens service life

The first two can be calculated. Downtime is often the largest, but the hardest to put a figure on, because it depends on what the machine should have been doing in the meantime.

What do frequent oil changes cost?

A gas engine on landfill gas at Enovert had its oil changed about 48 times a year, each time with about 500 litres of new oil and as much waste oil, plus labour and planned downtime.

With offline filtration in a kidney loop, the oil was changed according to its actual condition instead of a fixed number of hours:

Before After
Oil changes per year about 48 7
Oil life 1 time 7.2 times longer
New oil saved per year about 20,500 litres
Financial gain (estimated) about £80,000 in the first year, then about £68,000 a year

On three other gas engines, the oil change interval went from about 150 to an average of 650 operating hours.

What does a failure cost?

More than the spare part. A new baler costing around £500,000 had five failures in its first six months: two pumps and three valves. That cost around £15,000 in parts and labour, and nobody could find the cause until the oil analysis showed that dust was breaking down the oil. Since the filtration was installed, there has not been a single fluid-related failure.

At a factory with hydraulic presses running around the clock, there was at least one valve failure a week. Each valve cost around £20,000, and a replacement could take up to three days of maintenance work. Two years after installation there has not been a single valve-related failure, and today only the cartridges are changed, typically every 8 to 12 months.

What does downtime cost?

On a large hydraulic power unit for a test rig, technical interventions and downtime fell by 80 to 85 % after an offline unit was fitted. The customer itself estimates the payback time at under two weeks.

Downtime also hits systems that only need to run now and then. An emergency generator that will not start costs nothing on the day it stands still in the test. It costs on the day the power goes.

What does the filtration itself cost?

A kidney loop unit has three costs: the unit itself, the cartridges and the power for a small pump. The cartridges are changed to a fixed plan, which is adjusted once the used cartridges have been analysed.

Clean oil also makes the existing filters cheaper to run. On a port crane, the customer reported that the life of the engines’ own fuel filters at least tripled.

How do you find your own figure?

Start with the costs you know: how many oil changes you have a year, how much oil that is, and what the hours cost. Enter them in the calculator below, and choose yourself how many fewer changes you want to assume.

The calculator adds no assumptions. We measure the real figure for your system in a pilot programme with samples before, during and after.

What do your oil changes cost?

Enter your own figures. The calculator adds no assumptions apart from the reduction in oil changes that you choose on the slider.

Enter litres per change, changes per year and oil price to see the calculation.

Example: Enovert went from about 48 to 7 oil changes a year. Read the case study.

The figures stay in your browser and are not sent anywhere. We measure the real figure for your system with samples before and after in a pilot programme. How the pilot programme works.

Questions and answers

What does an oil change cost?

New oil, disposal of the used oil, labour hours and downtime. Enter your own figures in the calculator on this page. At Enovert, about 48 oil changes a year meant about 500 litres of new oil and as much waste oil each time.

How much can offline filtration save?

It depends on the system, and we do not promise a figure in advance. In the case studies, a gas engine went from about 48 to 7 oil changes a year, and a hydraulic press from weekly valve failures to none in two years. We measure the real figure for your system in a pilot programme.

What does a failure cost?

More than the part. At Stadco each valve cost about £20,000, and a replacement took up to three days of maintenance work. On top of that comes the production that stands still in the meantime.

How quickly does a unit pay for itself?

It depends on what the problem costs today. ORE Catapult estimates the payback time at under two weeks, because interventions and downtime fell by 80 to 85 %. Calculate your own oil changes in the calculator.

Want to know the figures for your own system?

We are happy to take a sample and go through the figures with you.